{"product_id":"hawk-performance-dtc-70-motorsports-brake-pads-coleman-series-iii-caliper-0-980in-thick","title":"HAWK Performance DTC-70 Motorsports Brake Pads Coleman Series III Caliper - 0.980in Thick","description":"\u003cdiv\u003e\n\u003cdiv\u003e\n\u003cp\u003eThe Hawk DTC-70 race compound was engineered with extremely high torque and highly aggressive initial bite for cars with high deceleration rates, with or without downforce. With superior release and control characteristics, it's a winning race solution on its own or as split friction with DTC-60.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003cp\u003eDTC-70 is more aggressive than the DTC-60 but has the same temperature range. Many racers of Corvettes, Mustangs, Porsches, BMWs and other specialty race cars choose to run DTC-70 Front and DTC-60 rear. This is not an entry level race compound and should not be driven on the street. Use when you are a serious racer with track experience and have had issues with less aggressive compounds overheating or not providing enough bite.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eHigh Performance\u003c\/li\u003e\n\u003cli\u003eHigh Torque\u003c\/li\u003e\n\u003cli\u003eSuperior Rotor and Pad Wear\u003c\/li\u003e\n\u003cli\u003eExcellent Modulation and Release Characteristics\u003c\/li\u003e\n\u003cli\u003eApplicable to NASCAR, NASCAR modified, ARCA, Super Late models, pavement circle track, Pro 2, Pro 4 Off Road Trucks, Pro Lite, Sports Car, GT, GS, Open Wheel, Formula, Monster Trucks\u003c\/li\u003e\n\u003cli\u003eStable Friction Output\u003c\/li\u003e\n\u003cli\u003e400-1600 Deg F Operating Temperature Range\u003c\/li\u003e\n\u003cli\u003e600-1200 Deg F Optimal Temperature Range\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFor motorsport use only. Image is for illustative purposes, actual product may differ.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003ch3\u003eHawk Brake Pad Installation Procedure\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eInstall Brake pads properly. Be sure pads are securely positioned in the caliper.\u003c\/li\u003e\n\u003cli\u003eFlush system with fresh brake fluid.\u003c\/li\u003e\n\u003cli\u003eCheck all hydraulic parts for excess wear and tear.\u003c\/li\u003e\n\u003cli\u003eCheck disc for proper thickness, parallelism, and lateral run-out.\u003c\/li\u003e\n\u003cli\u003eCheck disc for scoring or grooves over .012\"\" depth. If either applies, resurfacing or replacement is required.\u003c\/li\u003e\n\u003cli\u003eIf disc does not need resurfacing then contamination from the previous brake pads must be removed. Sand discs with Garnet sandpaper using moderate pressure. Use soap and water to clean off disc surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid\u003c\/li\u003e\n\u003cli\u003eInspect calipers for freedom of movement. Lubricate where necessary\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHawk Brake Pad Bedding Procedure - Motorsports Pads\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAfter reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times.\u003c\/li\u003e\n\u003cli\u003eAt higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times.\u003c\/li\u003e\n\u003cli\u003eAt or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion.\u003c\/li\u003e\n\u003cli\u003eDo not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch.\u003c\/li\u003e\n\u003cli\u003eIf during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant Reminders when Burnishing or Bedding Brake Pads\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDo not attempt to use badly worn or damaged rotors with new brake pads.\u003c\/li\u003e\n\u003cli\u003eDo not drag brakes while car is moving during break-in procedure.\u003c\/li\u003e\n\u003cli\u003eDo not engage pedal while car is stopped at any time following the break-in procedure.\u003c\/li\u003e\n\u003cli\u003eUpon completing the procedure, allow the brake system to completely cool before racing.\u003c\/li\u003e\n\u003cli\u003eApplying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds.\u003c\/li\u003e\nli\u0026gt;Clean a used rotor surface with fine sand paper or steel wool, rinse with water, dry and install before bedding new pads\n\u003cli\u003eSome forms of racing do not allow time for the proper break-in procedure to be performed. However, it is still very important to attempt to perform at least the core of the procedure: Build up heat slowly and allow the system to completely cool down before racing if possible.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"HAWK Performance","offers":[{"title":"Default Title","offer_id":55426078507389,"sku":"HWK-HB105U.980","price":401.24,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/5767\/7352\/files\/hawk-performance-dtc-70-motorsports-brake-pads-coleman-series-iii-caliper-0-980in-thick-874.webp?v=1741034073","url":"https:\/\/www.tegiwa.com\/products\/hawk-performance-dtc-70-motorsports-brake-pads-coleman-series-iii-caliper-0-980in-thick","provider":"Tegiwa","version":"1.0","type":"link"}