{"product_id":"hawk-performance-dtc-60-motorsports-brake-pads-stop-tech-st-22-caliper","title":"HAWK Performance DTC-60 Motorsports Brake Pads Stop Tech ST-22 Caliper","description":"\u003cdiv\u003e\n\u003cdiv\u003e\n\u003cp\u003eRunning with extremely high deceleration rates and increased downforce poses different challenges, so Hawk designed DTC-60 race compound. Recommended with DTC-70 when split friction between axles is desired, it has excellent modulation and release characteristics.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003cp\u003eDTC-60 has the same temperature range as DTC-70, but produces less brake torque. Many racers of lighter, smaller cars such as the Miata and S2000 will run DTC-60 Front and DTC-30 Rear. On larger, heavier, cars such as Corvettes, Mustangs, Porsches, BMWs and other specialty race cars, the DTC-60 is run on the rear with DTC-70 up front. This is not an entry level race compound and should not be driven on the street. Use when you are a serious racer with track experience and have had issues with less aggressive compounds overheating or not providing enough bite.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eSuperior Release and Torque Control\u003c\/li\u003e\n\u003cli\u003eVery Low Pad and Rotor Wear\u003c\/li\u003e\n\u003cli\u003eHigh Torque\u003c\/li\u003e\n\u003cli\u003eExcellent Modulation and Release Characteristics\u003c\/li\u003e\n\u003cli\u003eApplicable to NASCAR, NASCAR modified, ARCA, Super Late models, pavement circle track, Pro 2, Pro 4 Off Road Trucks, Pro Lite, Sports Car, GT, GS, Open Wheel, Formula, Monster Trucks\u003c\/li\u003e\n\u003cli\u003eStable Friction Output\u003c\/li\u003e\n\u003cli\u003e400-1600 Deg F Operating Temperature Range\u003c\/li\u003e\n\u003cli\u003e600-1200 Deg F Optimal Temperature Range\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFor motorsport use only. Image is for illustative purposes, actual product may differ.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv\u003e\n\u003ch3\u003eHawk Brake Pad Installation Procedure\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eInstall Brake pads properly. Be sure pads are securely positioned in the caliper.\u003c\/li\u003e\n\u003cli\u003eFlush system with fresh brake fluid.\u003c\/li\u003e\n\u003cli\u003eCheck all hydraulic parts for excess wear and tear.\u003c\/li\u003e\n\u003cli\u003eCheck disc for proper thickness, parallelism, and lateral run-out.\u003c\/li\u003e\n\u003cli\u003eCheck disc for scoring or grooves over .012\"\" depth. If either applies, resurfacing or replacement is required.\u003c\/li\u003e\n\u003cli\u003eIf disc does not need resurfacing then contamination from the previous brake pads must be removed. Sand discs with Garnet sandpaper using moderate pressure. Use soap and water to clean off disc surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid\u003c\/li\u003e\n\u003cli\u003eInspect calipers for freedom of movement. Lubricate where necessary\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHawk Brake Pad Bedding Procedure - Motorsports Pads\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAfter reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times.\u003c\/li\u003e\n\u003cli\u003eAt higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times.\u003c\/li\u003e\n\u003cli\u003eAt or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion.\u003c\/li\u003e\n\u003cli\u003eDo not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch.\u003c\/li\u003e\n\u003cli\u003eIf during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant Reminders when Burnishing or Bedding Brake Pads\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDo not attempt to use badly worn or damaged rotors with new brake pads.\u003c\/li\u003e\n\u003cli\u003eDo not drag brakes while car is moving during break-in procedure.\u003c\/li\u003e\n\u003cli\u003eDo not engage pedal while car is stopped at any time following the break-in procedure.\u003c\/li\u003e\n\u003cli\u003eUpon completing the procedure, allow the brake system to completely cool before racing.\u003c\/li\u003e\n\u003cli\u003eApplying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds.\u003c\/li\u003e\nli\u0026gt;Clean a used rotor surface with fine sand paper or steel wool, rinse with water, dry and install before bedding new pads\u003c\/ul\u003e\n\u003c\/div\u003e","brand":"HAWK Performance","offers":[{"title":"Default Title","offer_id":55426050523517,"sku":"HWK-HB180G.560","price":248.86,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/5767\/7352\/files\/hawk-performance-dtc-60-motorsports-brake-pads-stop-tech-st-22-caliper-112.webp?v=1741030368","url":"https:\/\/www.tegiwa.com\/products\/hawk-performance-dtc-60-motorsports-brake-pads-stop-tech-st-22-caliper","provider":"Tegiwa","version":"1.0","type":"link"}